Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Lewisville?
A chimney cap and crown job in Lewisville typically runs $525 to $2,650, depending on whether you’re capping a sound masonry chimney or rebuilding a cracked crown along with it. A standard stainless cap with a spark arrestor and animal screen usually lands between $350 and $675 installed. Crown repair is the wider range: minor sealing and crack patching sits around $400 to $900, while a full crown rebuild on a large multi-flue chimney can reach $1,900 to $2,650.
Those two pieces protect a lot. The cap keeps rain, birds, and squirrels out of the flue. The crown sheds water off the top of the masonry so it doesn’t soak into the brick and mortar below. When either one is missing or failing, water gets in and the deterioration that follows is always more expensive than the repair. We give free estimates and set the final price in writing, so you know the number before anything starts.
Chimney Cap & Crown Cost Breakdown (2026)
Here’s how the work breaks out for Lewisville homes. These are typical installed ranges for the local market.
| Item | Typical Installed Range |
|---|---|
| Single-flue stainless cap (with screen and spark arrestor) | $350 – $675 |
| Multi-flue custom stainless cap | $625 – $1,150 |
| Copper cap (single flue) | $550 – $950 |
| Copper cap (multi-flue) | $900 – $1,650 |
| Crown crack sealing and patch repair | $400 – $900 |
| Full crown rebuild (mortar crown, standard size) | $1,150 – $1,900 |
| Full crown rebuild (large multi-flue chimney) | $1,900 – $2,650 |
| Flue tile crown extension and wash | $650 – $1,250 |
| Cap and crown bundled | $525 – $2,650 (combined, varies with scope) |
What pushes a job toward the higher end? Size first. A single-flue chimney off a small fireplace is a simpler cap and a smaller crown than a chimney carrying two or three flues from a furnace, water heater, and fireplace all at once. Access matters too, since a steep roof or a tall chimney means more setup time. And the condition of the masonry underneath the crown is the biggest swing factor. If the crown has been cracked for a while and water has worked into the top courses of brick, we may find spalling mortar joints and loose brick that need repointing before a new crown can go on. That’s labor on top of the crown itself.
On the materials side, we work with professional-grade supply brands including Copperfield for caps and Gelco and HeatShield products for crown and masonry work. A custom-fabricated stainless or copper cap from a line like Copperfield fits the flue properly and lasts, which is why the material cost sits where it does. The brands matter here. We work with the same materials chimney engineers specify, not whatever a hardware store happens to stock.
What Affects Chimney Cap & Crown Pricing in Lewisville
- Number of flues. A single-flue chimney needs one cap opening; a multi-flue chimney needs a custom cap sized to span all of them, which costs more in both material and labor.
- Crown size and shape. A wide crown over a large chimney footprint uses more mortar and takes longer to form and cure than a compact one. Oversized or irregular crowns are priced accordingly.
- Condition of the masonry. A crown sitting on sound brick is a straightforward rebuild. A crown sitting on cracked, spalling brick means the top courses of masonry need attention first. That’s the difference between the low and high end of the crown range.
- Roof pitch and height. Lewisville roofs vary a lot. A steep pitch or a chimney set high on the ridge takes more setup and safety rigging than a low, accessible one, and that shows up in labor.
- Cap material. Stainless is the workhorse. Copper costs more up front and weathers to a patina, which some homeowners want for the look. Both come from professional supply lines.
- Whether a liner repair is needed underneath. If water has been getting past a failed crown for years, the flue liner may show deterioration. We check that during the inspection, and if a DuraFlex flexible liner system is part of the fix, that’s a separate line on the estimate.
One local note. North Texas summers bake the top of a masonry chimney, and the daily swing between hot afternoons and cooler nights works on a mortar crown year after year. That’s a big part of why crown cracks are common on older Lewisville chimneys, and it’s why we check the crown on every inspection rather than waiting for a homeowner to notice a leak.
Cap and Crown: Two Repairs, One Purpose
A cap and a crown fail in different ways and do different jobs, even though they sit at the same end of the chimney. Keeping them straight helps you understand what you’re paying for.
The crown is the sloped mortar top of the chimney itself. It’s supposed to shed water away from the flue opening and off the sides of the masonry. When it cracks, water runs into the chimney instead of off it. That water finds mortar joints, soaks into brick, and shows up inside the house as a stain on the ceiling or a damp smell when the fireplace isn’t in use. A crown rebuild means removing the old top, forming a new sloped crown, and sealing it so water runs where it should.
The cap sits above the flue opening on legs or a mesh frame. It stops rain from dropping straight down the flue, keeps birds and squirrels out, and a spark arrestor screen keeps hot embers from landing on the roof. A missing cap is often the reason a flue fills with water and debris between seasons. Together, a sound cap and a sound crown are the two things that keep the top of your chimney dry.
Because both pieces protect the same system, we check them together. A sweep without an inspection misses this kind of hidden deterioration, so we connect both steps by default. Our technicians have up to 14 years of experience reading the top of a chimney and knowing when a crack is cosmetic and when it’s letting water in.
Stainless, Copper, or Custom: Choosing a Cap
Most Lewisville homeowners are best served by a stainless cap. It’s durable, handles the heat, and the price range is the most reasonable of the options. A single-flue stainless cap installed runs $350 to $675. A multi-flue custom stainless cap sized to span several flue openings runs $625 to $1,150.
Copper is the upgrade. It costs more up front, roughly $550 to $950 for a single flue and $900 to $1,650 for a multi-flue, and it develops a patina over the years. If the chimney is visible from the street or the yard and you care how it looks, copper is worth considering. Either way, a properly fitted cap matters more than the metal. A cap that’s too small or badly mounted rattles, lets water in at the edges, and doesn’t keep animals out.
We fit caps from professional supply lines so the dimensions match the flue and the mounting holds. We’re not sizing a generic cap to a flue that’s a half inch off, which is the kind of thing that happens when a generalist handles the job.
Do You Need a Crown Rebuild or Just a Repair?
Not every cracked crown needs a full rebuild. A hairline crack that hasn’t spread, on an otherwise sound crown, can often be sealed and patched for $400 to $900. That’s a reasonable repair when the crown is still shedding water and the masonry below is tight.
A rebuild makes sense when the crown is broken through, crumbling, or has lost its slope so water pools on top instead of running off. That’s when a patch just delays the problem. A standard rebuild runs $1,150 to $1,900, and a large multi-flue chimney can reach $1,900 to $2,650. If the flue tiles need to be extended up through a new crown, that adds to the scope.
The honest answer is that you can’t tell from the ground. We check the crown during an inspection, look at how the masonry below it is holding up, and recommend the repair that actually solves the problem rather than the one that’s cheaper today. If a patch will hold, we’ll say so. If the crown is past patching, we’ll show you why.
How to Save on Chimney Cap & Crown
- Fix the crown before the masonry fails. A $400 to $900 patch now beats a crown rebuild plus brick repointing later. Water damage compounds, and the cost of the repair grows with it.
- Bundle the cap with the crown. Having both done in one visit saves on setup and access, since the technician is already on the roof. A combined job often costs less than two separate appointments.
- Get the inspection first. An inspection tells you whether you’re looking at a patch or a rebuild before you commit. We offer inspections as a standalone service, not just a sales pitch attached to a cleaning, so you get a straight read on what’s actually needed.
- Choose stainless unless you want copper for looks. Stainless does the job at the lower end of the range. Copper is worth it only if the appearance matters to you.
- Ask for a written estimate. The price is set per job by the written estimate, so there are no surprises when the work is done. Estimates are free, and you can call (888) 424-2086 to set one up.
One thing we won’t do is recommend a replacement you don’t need. Our material literacy across professional supply brands means we recommend based on what’s actually appropriate for your chimney, not on what’s easiest to sell. A cap that’s fine stays. A crown that can be patched gets patched.
Why a Failing Crown Is Worth Fixing Now
Water is patient. A cracked crown doesn’t fail dramatically. It lets a little water in every rain, and that water works on the mortar and brick below a bit at a time. Over a few seasons, spalling mortar joints and loose brick show up, and the fix that started as a crown patch becomes a crown rebuild plus masonry repair.
There’s a safety angle too. A chimney is a life-safety system. A crown that’s letting water into the flue can degrade the liner, and a deteriorated liner is a real risk when you light a fire. That’s why we look at the crown and the liner together during an inspection, and why we flag a failing crown rather than waiting for the homeowner to notice a leak. If the liner needs work underneath, a DuraFlex flexible liner system is a common fix, and HeatShield resurfacing can restore a ceramic flue in some cases without a full liner replacement. We work with those materials because they’re what the trade actually specifies.
Chimney work done right is thorough, and that’s the point. A quick cap slapped on a crumbling crown doesn’t solve the problem. We’d rather do the job correctly once.
Sweep to Repair: One Visit, One Crew
Cap and crown work is one part of the full chimney service cycle. We handle sweep, inspection, and repair together, so you’re not coordinating between a sweep company that finds a problem and a mason who fixes it and a third contractor who caps it. One visit can cover the cleaning, the inspection, the crown repair, and the cap install, with a written estimate for the repair work before it starts.
That matters for Lewisville homeowners with older masonry chimneys, where a crown issue often comes with a liner question and a creosote question at the same time. Connecting the steps means nothing falls between contractors. You can read more about how we approach the full system on our Lewisville Chimney Sweep page, and if you’re comparing local options, our Lewisville page covers the area we serve.
FAQs – Chimney Cap & Crown Cost
How much does a chimney crown rebuild cost in Lewisville?
A full crown rebuild in Lewisville typically runs $1,150 to $1,900 for a standard-size chimney, and $1,900 to $2,650 for a large multi-flue chimney. A patch-and-seal repair on a smaller crack runs $400 to $900. Call (888) 424-2086 for an exact quote – estimates are free.
How much does a chimney cap cost installed?
A single-flue stainless cap installed typically costs $350 to $675. A multi-flue custom stainless cap runs $625 to $1,150, and copper caps run $550 to $1,650 depending on the number of flues. Call (888) 424-2086 to get a written estimate for your chimney.
Is it cheaper to repair or replace a chimney crown?
Repair is cheaper when the crown only has a hairline crack, at $400 to $900 versus $1,150 to $2,650 for a rebuild. But a patch on a crown that’s broken through or lost its slope just delays the water damage, so the cheaper option isn’t always the right one. We check the crown and tell you which applies. Call (888) 424-2086 for a free estimate.
Can you install a chimney cap the same day?
Often, yes. A standard single-flue stainless cap can usually be installed the same day if we have the size on hand, and a custom cap takes longer to fabricate. Call (888) 424-2086. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Do I need a permit for chimney crown repair in Lewisville?
Most crown repairs and cap installations don’t require a permit, since they’re replacing existing components rather than altering the structure. But rules vary by project, so it’s worth a quick call to the city’s building department if your job involves structural changes. For the repair itself, call (888) 424-2086 and we’ll walk you through what’s involved.
Get a Free Cap & Crown Estimate in Lewisville
A sound cap and crown are the cheapest insurance your chimney has. We’ll inspect the top of your chimney, tell you whether you’re looking at a patch or a rebuild, and give you a written estimate before any work starts. We work with professional-grade brands including Copperfield, Gelco, and HeatShield, and our technicians have up to 14 years of experience. Call (888) 424-2086. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Estimates are free.
Pricing reflects the Lewisville market as of 2026. Lewisville Chimney Sweep offers free estimates – call (888) 424-2086.
Written by the team at Lewisville Chimney Sweep.
What Our Customers Say
"Thorough sweep and a clear report. He was running late from the job before and arrived near the end of the window, though he did call to warn me."
- Yolanda Vargas"Fireplace had never drawn properly since we moved in. He found the damper was only opening halfway due to a bent linkage and fixed it in ten minutes."
- Neil Novak"Crown was cracked and taking water. Repaired it rather than quoting a rebuild, which the previous company had pushed hard for."
- Angela Tran